Volkswagen Crafter Mk2 Accelerator Gas Throttle Pedal 2N2723503B

Volkswagen Crafter Mk2 Accelerator Gas Throttle Pedal is an original engine control system component for diesel-powered vehicles. It ensures precise transmission of the power demand signal to the ECU, which translates into stable throttle response and predictable vehicle behavior. This solution is dedicated to second-generation Crafter models, designed specifically for Diesel units and matched to the factory installation.

Specifications and technical data

• SKU: RHD-2N2723503B
• Mark: Volkswagen
• Condition: Used
• OEM Part Number: 2N2723503B
• Substitutable numbers: 2N2723503B, 2N2 723 503 B
• Fuel type: Diesel
• Category: Pedal Assemblies, Pads & Parts

Purpose and function in the powertrain

The accelerator pedal in the Volkswagen Crafter Mk2 operates within the electronic engine control system, replacing the traditional throttle cable. Its task is to generate a signal corresponding to the driver's foot position and transmit it to the engine controller, which then determines the fuel dosage and boost pressure. In Diesel vehicles, this is crucial for smooth acceleration, reducing jerking, and maintaining stable RPM under load.

A properly selected, original throttle pedal allows for maintaining the factory drive characteristics, which is particularly important in commercial vehicles where predictable throttle response, driver comfort, and consistent performance during daily operation are essential.

Construction and fitment for the Volkswagen Crafter Mk2

The presented accelerator pedal belongs to the Pedals, pedal pads, and footrests category, meaning it is factory-adapted for operation in the driver's cabin floor area. It has been designed with ergonomics in mind – appropriate tilt angle, travel, and resistance force, so that the driving feel is consistent with Volkswagen's factory specifications.

Original mounts and the electrical connector allow for installation in place of a worn-out component without the need for system modifications. As a result, the replacement process is predictable, and the risk of compatibility issues or engine control unit errors is minimized.

Benefits of using an original used throttle pedal

Using an original, used accelerator pedal in the Volkswagen Crafter Mk2 allows for maintaining consistency with the factory engine control system. A component originating from the same product line as the original factory-fitted part usually works better with the vehicle's electronics than replacements with uncertain parameters. This is especially important in delivery vans, where the appearance of errors in the control system can result in vehicle downtime.

Choosing an original used part is often a reasonable compromise between cost and quality – it allows for reduced expenses compared to a new component, while maintaining the correct operating characteristics and fitment for a specific diesel engine version.

Installation area and related components

The accelerator pedal operates in the immediate vicinity of other driver control components, such as the brake or clutch pedal. When working in this area, it is worth paying attention to the mechanical condition of the mounts, the cleanliness of the area, and the correct routing of the electrical harness. A properly installed throttle pedal should move smoothly throughout its entire range, without sticking or excessive play, and the electrical connector must be securely seated to avoid signal interruption while driving.

If you are planning a comprehensive repair or upgrade of the pedal control area in your Volkswagen and need other components from the same group, such as pads, additional footrests, or other pedals, check the available parts in the Volkswagen Pedals, pedal pads, and footrests category.

Additional technical and operational information

In diesel vehicles, throttle response is closely linked to the ECU software and the characteristics of the sensors in the accelerator pedal. Therefore, when replacing this component, it is worth ensuring correct seating and – if the service procedure for a given unit requires it – performing an adaptation in the engine controller. This helps avoid throttle response delays, uneven operation at low speeds, and unwanted error messages.

For fleet users and workshops servicing delivery vehicles, it is also important that using the correct accelerator pedal helps maintain consistent fuel consumption and stable operational parameters across the entire fleet, which facilitates cost planning and service scheduling.

To better understand when choosing original used components is cost-effective compared to remanufacturing, it is worth reading the guide: Manual transmission failures – why an original used part is sometimes a more reasonable choice than remanufacturing.